Roland VE-7000 Manuale del Proprietario

Owner’s ManualBefore using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (Owner’s Manual p. 2, 3; p.

10 Before you begin Update the VM Console In order to connect the VE-7000 to a V-mixing console and use it as a controller, the VM Console must be us

11Before you begin Save your data 1 Insert the data memory card (2--16 MB) that you normally use. 2 Turn on the power of the console. 3 Hold down [SH

12Before you begin 3 Release the buttons when “ ∗∗∗∗ ” is indicated in the display. 4 Turn off the power of the VM system when “VM-7000 updated. Rebo

13Before you begin 7 Hold down [SHIFT] and press [PROJECT]. The SYSTEM MENU will appear. 8 Select “MEMORY CARD.” 9 Select the “LIBRARY” page. 10 In L

14 Make connections Connect the necessary devices as shown in the following diagram. fig.connect Use a MIDI cable to connect the VE-7000's MIDI

15 Turning on the power 1 Turn on the power of the peripherals. 2 Turn on the POWER of VE-7000. Make sure that the POWER/MIDI indicator lights. Basic

16Turning on the power Operations in the CH VIEW screen You can edit the various parameters in the channel edit CH VIEW page.Accessing the CH VIEW pa

17Turning on the power DELAY/DYN AREA DIRECT/THRESHOLD Direct sound level for DELAYThreshold level for DYNDELAY LEVEL/RATIO Delay sound level for DEL

18Turning on the power CH VIEW area functions In the CH VIEW area you can access the CH VIEW page and switch between CH VIEW screens. Accessing the C

19 Convenient functions to remember By holding down the [SHIFT] button of the VE-7000 and pressing the following buttons, you can use the following c

2USING THE UNIT SAFELY USING THE UNIT SAFELY • Before using this unit, make sure to read the instructions below, and the Owner’s Manual.• Do not open

20 Operations in the channel edit pages (connected to the VM Console) By pressing [EDIT] in the various areas, you can access the pages corresponding

21 Using the joystick to control surround (connected to the VM Console) You can use the joystick (located in the SURROUND area) to perform surround p

22Using the joystick to control surround (connected to the VM Console) Using the joystick to control surround panning 1 Press SECTION [INPUT] (or [M

23 Troubleshooting If the VE-7000 does not operate as you expect, please check the following points first.• None of the controls work ● The power is

24 MIDI Implementation 1. THRU'ed data All data received at MIDI IN will be transmitted from MIDI OUT. This is called “Thru.” The data that is “

25MIDI Implementation 3. Control data transmission address map The exclusive messages transmitted when you operate the panel buttons, dials, or joys

26MIDI Implementation 4. Control data transmission data The following data is transmitted by each type of controller. 01H Transmitted when pressed 02

27 MIDI Implementation Chart Transmitted Recognized Remarks Function... Basic Default x x Not defined Channel Changed x **************

28 Specifications VE-7000:CH EDIT CONTROLLER• ConnectorsMIDI Connectors (IN, OUT)AC Adaptor Jack (DC IN)• Dimensions253.5 (W) x 169.5 (D) x 67.0 (H)

29MEMO

3USING THE UNIT SAFELY • Do not force the unit’s power-supply cord to share an outlet with an unreasonable number of other devices. Be especially car

30MEMO

InformationWhen you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.As of

32MEMO

For the USAFEDERAL COMMUNICATIONS COMMISSIONRADIO FREQUENCY INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits f

02455390 ’01-4-D2-31N

4 Contents USING THE UNIT SAFELY...2Contents ...

5 - IMPORTANT NOTES In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Power Supply • Do

6 Main features The VE-7000 is a channel edit controller that enables a revolutionary leap in efficiency when operating the channel parameters of a V

7 Names of Things and What They Do Front panel The front panel is divided into the areas shown below. fig.area 1 PREAMP AREAControl the parameters of

8Names of Things and What They Do 5 MAIN/CUE AREAControl the parameters of the channel edit MAIN/CUE page. 6 SURROUND AREAControl the parameters of t

9Names of Things and What They Do Rear panel fig.rear 1 MIDI connectors (MIDI IN/OUT) These connectors are used to connect MIDI devices.MIDI OUT is n